| SR 1848-1 code | C17 |
|---|---|
| Name in the standard | No vehicles higher than 2.15 m |
| Type | Prohibition or restriction road sign |
| Shape and colours | White disc with a red border, with the value 2.15 m between two black vertical arrowheads |
| Value shown | 2.15 m |
| Size | 40 cm diameter |
| Format (SR 1848-2) | Small |
| Material | Galvanised steel sheet, 1 mm |
| Construction | Pressed edges, no sharp edges |
| Painting | Electrostatic, UV-resistant paint |
| Retroreflective sheeting | Class I (RA1), UV-resistant |
| Retroreflection (white, 0.2°/5°) | 70 cd/(lx·m²) |
| Sheeting service life | 7 years |
| Weight | 2 kg |
| Fixings included | 2 clamps, with bolts and nuts |
| Post diameter | Ø48 mm (Ø60 mm on request) |
| Standards | SR EN 12899-1:2007, SR 1848-1:2024, SR 1848-2:2011, SR 1848-3:2011 |
| Marking | CE |
| Height | 40 cm |
The C17 stops the driver of a vehicle taller than 2.15 m before reaching a bridge, underpass or portal it will not fit under. The value sits between two black vertical arrowheads. This version is Ø40 cm, the small format in SR 1848-2, intended for low-traffic minor roads.
Class I (RA1) sheeting returns 70 cd/(lx·m²) for white to the driver and has a 7-year service life, enough on roads where headlights are the only light: local, minor and private roads or quiet streets. In areas with street lighting, shop windows, advertising and dense urban traffic, however, SR 1848-2 requires prismatic class 2 or 3 sheeting.
It goes at both ends of bridges, underpasses, tunnels, portals and other places where the 5.50 m clearance height is not available, and at the junction leading to an alternative route; there, as with the C16, the P4 panel with the distance is added.
As a general rule for prohibition and restriction signs, it goes right after the junction before the restricted section, so the drivers concerned can take another route without having to turn back. The sign is repeated after every junction on the section, for drivers joining from side roads, and if the restriction starts further on, the P4 additional panel with the distance goes under it.
Fixings for the post are included: 2 clamps for Ø48 mm posts, with bolts and nuts; clamps for Ø60 mm posts are available on request. The bottom edge of the sign goes 1.50–2.50 m above the road or kerb, and the edge nearest the road 0.50–2.0 m from the road platform. The sign must be visible from at least 50 m in built-up areas and 100 m outside them.
The post is ordered separately. For a fixed installation in a concrete foundation: the galvanised Ø48 mm post, 300 cm. For temporary use, with no foundation: the Ø48 mm tripod post, 120 cm. On concrete or paving, where you cannot dig: the Ø60 mm flange post, 300 cm, bolted down; for it, ask for the Ø60 mm clamps when you order.
The 40 cm diameter is the small format in SR 1848-2, meant for low-traffic minor roads and for short-term police signing at accident scenes. County and local roads, streets and private roads open to public traffic call for the normal Ø60 cm format: the C17-2.15. In car parks and private premises closed to public traffic the standard is not mandatory, so the small format is enough there.
It goes at both ends of bridges, underpasses, tunnels, portals and other places where the 5.50 m clearance height is not available, and at the junction leading to an alternative route; there, as with the C16, the P4 panel with the distance is added.
On low-traffic minor roads, for short-term police signing and in car parks or private premises closed to public traffic, where the standard is not mandatory. County and local roads and streets call for the normal Ø60 cm format: the C17-2.15.
The bottom edge goes 1.50–2.50 m above the road or kerb, and the inner edge 0.50–2.0 m from the road platform. The pack holds 2 clamps for Ø48 mm posts, with bolts and nuts; clamps for Ø60 mm posts are available on request.
Where the sign does not compete with other lights: on roads and streets without strong lighting, on local, minor or private roads. In areas with many light sources (street lighting, shop windows, advertising), SR 1848-2 requires prismatic class 2 or 3 sheeting.
The sheeting is class I (RA1), with a 7-year service life. Under SR 1848-2, during that time retroreflection stays at no less than 80% of the initial minimum value and the sheeting stays bonded over at least 95% of the surface.
10 cm less than the actual clearance height, rounded down to the nearest 5 cm. For example, under a bridge with 2.25 m of clearance the C17 shows 2.15 m.
The P34 (except residents) or P18 (exempting certain vehicle categories) additional panel goes under the sign, adapted to the exempted category.
Yes. SR 1848-1:2024 requires prohibition and restriction signs to be repeated after every junction on the restricted section, so that they also apply to drivers joining from side roads.
Yes. It is CE marked and complies with SR EN 12899-1:2007, the European standard for vertical road signs, and with SR 1848-1:2024, SR 1848-2:2011 and SR 1848-3:2011. The sheeting and the paint resist UV and weathering.
Yes. You order directly on the site, as an individual or a company, and pay by card or cash on delivery.
Yes. Every order comes with a tax invoice, issued to an individual or a company.
Yes. Public institutions find us in SICAP as S.C. ATTO REGAL S.R.L. Our company details are on the Purchase through SEAP / SICAP page.
We deliver by courier within 24-48 hours.
Yes. As a private individual you can return the product within 14 days of receiving it, as the law provides, and you get your money back within 14 days of telling us. Return shipping is paid by the customer. The full terms are on the Return policy page.
Get a personalised offer, transport included.
Sending this form is not an order.
We will send you the offer, transport included, as soon as possible by email or phone.
Atto Trafic supplies complete road signage and safety equipment — signs, traffic signs, markings, parking barriers, speed bumps, mirrors, bollards and accessories.